All Categories
EN

Products

Home>>Products>RTU Enamel Powder>Black RTU Enamel Powder for Stoves, Ovens and BBQ Grills

Contact Us

+86-13574208778

+86-13574208778

jack@nolifrit.com

Building 4, Power Valley Industrial Park, Majiahe Street, Tianyuan District, Zhuzhou City, Hunan Province, China

Black RTU Enamel Powder for Stoves, Ovens and BBQ Grills

Black RTU Enamel Powder for Stoves, Ovens and BBQ Grills


A black ready-to-use powder for wet-process enameling of steel - two fineness classes, plus an acid-resistant option and a matte finish in the same family.

Product Description

Black ready-to-use enamel powder for wet-process application on steel, fired at a nominal 850 °C. Offered in two fineness classes for stove plates, oven panels and trays, and grill bodies, with an acid-resistant option and a matt finish in the same family.

  • ProcessWet
  • Firing850 °C nominal
  • ColourBlack
  • FinishGlossy / Matt

Fineness classes

Two fineness classes are used for this application. The class that suits a part is settled with us against the part and the coating route; no fineness figure is quoted here because the two grade data sheets record sieve residue in different ways.

What the material does well

  • Two fineness classes. A coarser and a finer class are used for the same application, so the class can follow the part rather than the other way round.
  • An acid-resistant option. Where an acid-resistance requirement applies to the part, the acid-resistant grade is specified; where none applies, the standard grade is.
  • A matt finish in the same family. Where the drawing calls for a matt surface, the matt grade is specified instead of the glossy one.

Technical data

Product specifications — common to the grades on this page

Parameter Specification
Application method Wet process (slurry)
Firing temperature 850 °C (reference value, on steel; not a fixed setting for every part)
Colour Black
Surface finish Glossy (matt grade offered separately, see below)

Substrate and pre-treatment requirements are set out on the data sheet of the grade you specify.

Differences between the grades

Parameter Standard fineness Fine grade Acid-resistant
Acid resistance - - A+
Specify it when No acid-resistance requirement applies A finer coating is called for on the part An acid-resistance requirement applies to the part

A+ is a result recorded on the citric acid test, not a certified or general rating. A dash means that the data sheet of that grade does not list the item; it is a statement about the data sheet, not about the material.

Matt finish grade

Parameter Specification
Application method Wet process (slurry)
Firing temperature 850 °C (reference value, on steel; not a fixed setting for every part)
Colour Black
Surface finish Matt
Acid resistance -

The data sheet for this grade makes no acid-resistance claim. A dash means that the data sheet of that grade does not list the item; it is a statement about the data sheet, not about the material.

What the line has to provide

  • Substrate and pre-treatment. As set out on the data sheet of the grade being used, before the part reaches the coating stage.
  • Slurry preparation. The slurry is prepared to the grade data sheet; water addition and slip density follow the sheet and the plant.
  • Furnace capability. A furnace able to reach the nominal 850 °C with the load in it.
  • Firing conditions assessed on the part. The setting and dwell that suit a given part follow its size, mass and geometry and the way the furnace is loaded, and are agreed with our technical team.

Outside this range: the grades on this page are for steel parts in the applications above. Where a part is cast iron, or is in stainless steel, aluminum, galvanized steel or pre-coated steel, the route is assessed separately with our technical team.

Questions we are asked

Which of the two fineness classes should we specify?
It follows the part and the coating route. Send the part drawing and the route you have, and we will confirm the class.
Does the acid-resistant grade come with slurry parameters?
No separate slurry figures are quoted for it here. Slurry settings follow the data sheet of the grade and the plant.
Can these grades share a line?
They are applied by the same wet route. Whether a given line can run both without changeover sits with the plant; we will go through it with you.

Next step

Send the part, the substrate and your firing conditions. We will confirm the grade, the fineness class and the firing assessment from there.

Send the part details

Values describe the grades, not a guarantee for a particular part. The data sheet issued with a quotation carries the binding figures.